ANCEL V6 PRO ALL IN ONE TABLET DIAGNOSTIC TOOLS

ANCEL V6 PRO all-in-one table diagnostic tool is an upgrade of ANCEL V6. It has more powerful functions than V6, added more 10 special reset functions (at total 25 Resets) such as A/F SET,DOOR&WINDOWS, LANGUAGE, NOX SET,  PUMP START,  SEAT SET, START&STOP, TIRE SET,  TRANSPORT,  UREA SET and so on. It can also support full system , ECU Coding and Active Test. 2 year free update , B-luetooth connection saving your more times.It is the best choice for DIY diagnostic scanner tools.

OE-LEVEL Full System Diagnostic 

Brake System : if you feel the brake pedal is mushy and notice unusual odor or noise, etc. A properly operating brake system is critical to ensure safe vehicle control and operation;

Emission System : if the system is affected by vehicle age or poor quality fuel. A good emission system reduces harmful gases to a large degree and protects you from being fined;

Fuel system : if vehicle won’t start or “Check Engine” light is illuminated. Check car’s fuel system regularly ensures the best performance of your car with the lowest emissions;

Transmission System : if your car is slipping or difficult to shift. The system plays an important part in the overall performance of your car;

Light System : if you see rapid signal blinking or dimming lights.

Wiper System : if you observe chattering or streaking wiper. If the car is not regularly checked, the accident might happen because you can’t see clearly;

And many more ...

Support 25 Reset Functions

1.Oil Reset Service:

Allows you to perform reset for the Engine Oil Life system, which calculates an optimal oil life change interval depend on the vehicle driving conditions and climate.

2.EPB Service: 

Helps maintain the electronic braking system safely and effectively, deactivating and activating the brake control system, assisting with brake fluid control, opening and closing brake pads, and setting brakes after disc or pad replacement, etc.

3.ABS Bleeding:

ABS brake bleeding to get a firm brake pad after air exhaustion.

4.BMS service: 

Allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle.

5.TPMS service:

Makes sense in displaying sensor IDs from the vehicle's ECU, inputting TPMS sensor replacement IDs and testing sensors.

6.DPF Service:

Allows you to carry out numerous functions to the Diesel Particulate Filter system.

TPMS Service: Allows you to quickly look up the tire sensor IDs from the vehicle’s ECU, as well as to perform TPMS programming and reset procedures after tire sensors are replaced.

7.IMMO Service: 

Programs a new anti-theft key, and performs key matching when the ignition switch, the combined instrument panel, ECU, BCM, or the remote control battery is replaced.

8.SAS steering angle sensor service:

helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.

9.Injector Coding:

Leaking injectors and some dead injectors can be missed even when an injector is disabled. Other problems with the ignition system and mechanical components also may not show an rpm loss when an injector is turned off

10.TPS Throttle Adaptation

The throttle body is a tube containing a pivoting flat(butterfly) that is used to control the amount of air entering an engine. In an electronically fuel injected car , a throttle position sensor and air flow sensor communicate with the computer , which

supplies the corresponding amount of fuel needed at the injectors. It must need re-learning throttle sensor position after

clearing or repair

11.AT Set

12.Gear Learning

Crankshaft position sensor adaptive learning.

13.Headlight Reset

Allowing for adaptive headlights to be relearnt.

14.Suspension

15.Sunprrof

16. A/F Reset

This function is applied to set or learn Air/Fuel ratio parameters.

17.Door & Windows Calibration

This feature is designed to perform door window matching to recover ECU initial memory,and recover the automatic ascending and descending function of power window.

18.Language Change

This function is used to change the system language of the vehicle central control panel.

19.Nox Sensor Reset

Nox sensor is a sensor used to detect the content of nitrogen oxides (NOx)in engine exhaust.If the NOx fault is re-initialized and the NOx catalytic converter is replaced,it is necessary to reset the catalytic converter learned value stored in the engine ECU.

20.PUMP START

21.Seat Calibration

This function is applied to match the seats with memory function that are replaced and repaired.

22.Stop/Start Reset

This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware)

23.Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

24.Transport Mode

In order to reduce power consumption,the following functions may be disabled,including limiting the vehicle speed,not waking up the door opening network,and disabling the remote control key,etc.At this time,the transport mode needs to be deactivated to restore the vehicle to normal.

25.Adblue Reset

After the diesel exhaust treatment fluid (car urea) is replaced or filled up,urea reset operation is required.